Reply to Thread

Post a reply to the thread: CPS plugs missmatched

Your Message

Click here to log in

Please correctly re-type the phrase f o o t d o c t o r in the form box. Re-type it without the extra spaces and put the one space where it should be. We apologize for having to do this but this silliness helps slow the spammers.


Additional Options

Topic Review (Newest First)

  • 02-12-2009, 08:20 AM

    don't consult the Bentley in this case

    it is wrong

    on page 260-11 they are telling about the procedure of replacing the CV joint of the driveshaft. The drawing is actually showing a driveaxle. These axles do have CV joints, but don't requiring taking out the driveshaft.....driveaxles are discussed in another chapter.

    M70 engine only: on page 100-9, second picture from above, they are telling that the fuel pump relays are at location B1/B2 and the main relays at A1 and B1(!). This is actually wrong. At location A1/A2 are the fuel pump relays, at B1/B2 the main relays. On page 130-8, the first picture from above, the same mistake is made. This is double checked in the original factory manual.

    Most owners of the book don't know this one: the 2 bimmers shown on the cover of the book aren't actually E32 models, but in fact E38 models (later model, different car). I'll bet some guys are start running to their book right now ;-)

    M70 engine only: at page 120-10, 2nd picture down, the picture shows the plugs for the crankshaft sensor and cylinder identification sensor (pulse wire). According to Bentley, the 2 top plugs are the crank sensor plugs, and the bottom 2 are the ones that go to the spark plug wires. This is obviously wrong. Looking at the picture, the left top plug is the crank sensor bank 1-6, left bottom plug is the spark plug sensor bank 1-6, right top plug is the spark plug sensor bank 7-12 and finally right bottom plug is the crank sensor bank 7-12. Also this is checked in the factory manual.

    M70 engine only: at page 113-26 they say that the tightening torque of the intake manifold to cylinderhead is 22 Nm(17ft-lb). Don't do this! If you tighten those small nuts with that amount of torque, the bolts will break. The proper torque is: 10 Nm(7ft-lb) for the manifold to gasket nuts (M6), and the gasket to cilinderhead nuts (M8) is 24 Nm( about 18ft-lb).

    M70 engine only: at page 113-26 they are talking about the intake manifold removal. The fourth line of text from above stated 'remove throttle housings from intake manifold'. That is totally unnecessary when removing the intake manifold. Thats just another gasket to replace, risk of false air etc. You can leave the throttle bodies (DK motors) attached to the manifolds without any problem.

    Comments found on the net (not verified yet):

    "One comment I have about the Bentley manual is that they suggest removing the fan and shroud to gain better access to the thermostat. This is totally unnecessary: I was able to get to all four bolts and replace it easily without removing anything else."

    If you know (or find) any more errors in the Bentley manual, please report them to us so we can publish them here.

    Shogun E32 Tech Tips:
  • 02-11-2009, 03:21 PM

    CPS plugs missmatched

    Hi guys,

    I need help figuring out how to plug back in my CPS and Sparkplug timing plugs. The 4 plugs that are in front of the injector harness. I got the orders mixed up. Anyway to tell which one goes where (#'s or identification marks)? Left or right bank?

Posting Permissions

  • You may post new threads
  • You may post replies
  • You may not post attachments
  • You may not edit your posts
1e2 Forum