+ Reply to Thread
Results 1 to 15 of 15
Thread: Sagging door trim
-
03-28-2007 04:13 PM #1
-
-
03-28-2007 07:17 PM #2
I used 3M Weatherstripping Adhesive (08008)
I picked up a 5oz. tube of it at the local NAPA auto store for about $12 (CDN).
The 3M Id# is: 60-9800-3122-7
Follow the instructions, support with masking tape until it sets, and you're done. I did this last summer and it's still holding strong.
Hope this helps.
Regards
Glenn
-
03-28-2007 07:21 PM #3
-
03-28-2007 09:27 PM #4
-
03-29-2007 07:03 PM #5
-
03-30-2007 10:26 AM #6
-
07-02-2008 09:51 PM #7
Re: Sagging door trim
This problem happened to my 2004 330ci on the passenger side. The felt trim forward of the overhead handle just popped off from the rubber door seal on the hottest day in London. The trim is quite taut, and there's no way to stick it back using glue without a clamp or something to hold the trim in place while the glue dries. Even then the trim will constantly pull on the rubber and eventually tear the glued surfaces apart again.
I used no-more-nails/liquid-nails at the beginning and tried to hold the trim in place. But it would take so long for this stuff to dry that it simply wouldn't work. Now I made a total mess of it because the stuff is white in colour and the b*tch trim is hanging lose with the white stuff showing on the gluing surfaces.
This is seriously p*ssing me off as this is a design fault, and I would have to pay around 500GBP plus my lost time to get the whole door seal plus trim replaced at a dealer. I don't really feel BMW or their dealers deserve my money because for all I know this could be a deliberate flaw for them to make money.
Anyway I spent a whole day searching for a super glue that is strong enough and dry fast enough to fix the trim quickly. I had considered the messy 2 part epoxy glues. Then I would have to buy a small artist's brush to apply the glue. The whole thing is a hassle and there's no guarantee of success because the trim would just keep pulling on the gluing surfaces.
After a lot of thinking time, I think I have finally found the solution. I had on various occasions used the bathroom silicone sealant to stick things together, and it comes in a translucent/transparent colour. The bond created by the sealant is quite strong and lasts for very long time. All I have to do now is cut the loose hanging trim somewhere innocuous like above the passenger's head. The cut would eliminate the trim's pull on the glue. Then I can use the sealant to glue the trim back easily. The cut in the trim would probably open a small gap. I'll be happy to live with that and I might just fill it with the transparent sealant if the gap is small enough.
-
07-03-2008 01:10 PM #8
On another thread, others have tried....
Others seem to have had good success with either of the following products.
a) Loctite Extreme, or
b) Gorilla Glue
There's a discussion on it on another thread, here...
http://bimmer.roadfly.com/bmw/forums...8969894-1.html
Hope this helps
Glenn
-
07-03-2008 01:11 PM #9
-
07-03-2008 04:40 PM #10
-
07-06-2008 07:05 PM #11
-
07-06-2008 08:07 PM #12
-
04-02-2010 04:32 AM #13
-
04-10-2010 10:04 AM #14
-
04-10-2010 09:18 PM #15
- Location
- San Mateo, CA, United States
Member No: 24397
- Join Date
- Jan 2002
- Posts
- 5,074
- Rep Power
- 22
I have a few questions, if you don't mind.
I have tried and failed many times to repair these. Latest attempt was double stick tape, failed in days. Should have guessed.
I believe my failure is related to technique, and not adhesive.
My first question is: Do you garage your car the majority of the time, or do you live in an area where you do not regularly see high temperatures, or much direct sunlight? I believe that my outdoor parking and high levels of sun, and relatively high heat might be contributing to higher failure rates.
In my previous attempts (especially with the 3M weatherstrip adhesive, and later with epoxy), I had the window down, and used blue painters tape to secure the trim to the car. I am wondering if the window should be up, that way the trim seats more naturally with the position of the glass. Same goes for the door on the sides. I secured the trim with tape, with the door opened until the adhesive cured. I am thinking it would seat more naturally with the door closed.
Can you elaborate on your technique that has worked successfully?
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Bookmarks