+ Reply to Thread
Results 1 to 11 of 11

Thread: Z3

  1. #1
    Registered Member
    Location
    , , United States
    Member No: 143965 OnRadar is an unknown quantity at this point OnRadar's Avatar
    Join Date
    Aug 2006
    Posts
    27
    Rep Power
    0


    Yes | No

    Z3

    Newby for the Z3 arena so sorry if this is a repeat question. Just bought a 2001 Z3 (3.0). I might have a chance to get a free set of old snow tires/rims for a 2003 Z4 (3.0)...would these fit on the Z3?

    Also, "service engine" light comes on for a day or two, then will go off for a day or two. It does not flash. Initially the dealer (chevy) said it just needed a new battery and it was replaced. A week later, light came on for 2 days, now its off again...any advice?


  2. #2
    BZN Z3
    Guest
    Location
    , ,
    Member No: BZN Z3's Avatar


    Yes | No

    Re: Z3

    Have the codes read. Or by yourself a Peake tool and do it your self.

  3. #3
    ghpup
    Guest
    Location
    , ,
    Member No: ghpup's Avatar


    Yes | No

    Re: Z3

    Personally, I'm not much for driving the Z3 in the snow. Z3's of that year had 17in rims standard I think, but could use 15 and/or 16 inch rims. You'd be better off with a 15" or 16" rim with snows anyway. In regards to the service engine light, I recommend taking it to a decent independent that works regularly on BMWs. They'll tell you what is wrong and if it is critical.

  4. #4
    ghpup
    Guest
    Location
    , ,
    Member No: ghpup's Avatar


    Yes | No

    Re: Z3

    to add.... check out Tirerack.com or Bavaian Autosport (bavauto.com) other tire sellers to see if they comprable wheel styles and sizes listed for the Z3 of that year.

  5. #5
    Registered Member
    Location
    Oceanside, CA, USA
    Member No: 149143 lpcapital is an unknown quantity at this point lpcapital's Avatar
    Join Date
    Jan 2007
    Posts
    2,437
    Rep Power
    0


    Yes | No

    No Bavarian Autosport....

    forget their names: too many bad stories. They have the bad habits of advertising parts as OEM but then send you a Chinese replica that regularly fails... Sometimes catastrophically.

    There's few places that I can recommend hands down: one of them is oem****************...

    The Z3 & Z4 have the same rims/tires so the one on the Z4 would fit your car perfectly. We have only on set of rims with snow or A/S tires and we switch them from one to the other depending on which we take snowboarding.

    As for the CEL it could be one of two things (well, could be many things, but these are the popular picks), generally:
    1) check the rubber intake boot, going from the air filter housing to the throttle body. It always cracks around the harmonic of the slit that goes to the idle control valve
    2) the exhaust camshaft sensor has gone south. In the case A MUST is to buy it from the dealer or bet the BMW one from oembimmerparts. The aftermarket sensors will fail again. In this case you'll need a code reader to diagnose it.

    Welcome to the Z3 crowd!!!!!
    ---------------------------------



    1998 Z3 1.9 - few modifications here and there
    1999 Z3 2.8 - individual edition (British Traditional)
    2003 Z4 2.5i


  6. #6
    Registered Member
    Location
    , CA, United States
    Member No: 21426 wpballa is an unknown quantity at this point wpballa's Avatar
    Join Date
    Dec 2001
    Posts
    106
    Rep Power
    0


    Yes | No

    Check for a loose gas cap


  7. #7
    Registered Member
    Location
    , , United States
    Member No: 143965 OnRadar is an unknown quantity at this point OnRadar's Avatar
    Join Date
    Aug 2006
    Posts
    27
    Rep Power
    0


    Yes | No

    Re: Z3

    Thanks All! Checked the gas cap, no issue there. and set up a visit with my mechanic to have the codes looked at. Hope to Z you around!

  8. #8
    Registered Member
    Location
    , , United States
    Member No: 143965 OnRadar is an unknown quantity at this point OnRadar's Avatar
    Join Date
    Aug 2006
    Posts
    27
    Rep Power
    0


    Yes | No

    Re: No Bavarian Autosport....

    I'll save that site. Thanx for the welcome the Z3 is acually my girlfriends, the Boxster S is mine....now the race is on to see who can "not" get a ticket by summer's end ;)

  9. #9
    Registered Member
    Location
    Modesto, CA, United States
    Member No: 95616 scottpettit is an unknown quantity at this point scottpettit's Avatar
    Join Date
    Dec 2003
    Posts
    2,509
    Rep Power
    0


    Yes | No

    Let keep things simple....more

    Don't just check the gas cap, put a dab of oil on the gasket or better yet, replace the gasket for a buck or so at your dealer. It may take several start / stops over a couple of days for the CEL to reset if the cat is the cause.

    Go to Kragen / Auto Zone / Pep Boys- they will usually check your codes for free.

    If you are serious about doing your own work, get a PEAKE code reader.

    Welcome to this forum.

    Be sure to check out the Z Series Car Club of America at www.zscca.org
    we are holding our annual national event in Southern California this Labor Day weekend. You can check out the event at www.zfest.com

    Scott Pettit
    President
    ZSCCA

  10. #10
    Registered Member
    Location
    , , United States
    Member No: 143965 OnRadar is an unknown quantity at this point OnRadar's Avatar
    Join Date
    Aug 2006
    Posts
    27
    Rep Power
    0


    Yes | No

    Re: Let keep things simple....more

    Thanks, I have an autozone just down the road I'll see if they can check the codes. Also thanks for the news of the zfest!

  11. #11
    Registered Member
    Location
    Auburn, CA, United States
    Member No: 40215 DaneKane is an unknown quantity at this point DaneKane's Avatar
    Join Date
    Jun 2002
    Posts
    2,147
    Rep Power
    0


    Yes | No

    ...or just "flip-it!"..(the gas cap gasket)...

    ..remove gas cap gasket(2ez)..flip it over and you have a "new" flat mating surface..issue with caps is often due to corrosion on filler lip(ALL are effected)..i put a light smear of petroleum jelly on gasket with each refill..keeps surface clean and smooth..Z3 Cheers! dk '97 2.8 bg R

+ Reply to Thread


Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

     

Bookmarks

Posting Permissions

  • You may post new threads
  • You may post replies
  • You may not post attachments
  • You may not edit your posts
1e2 Forum