+ Reply to Thread
Results 1 to 9 of 9
  1. #1
    Registered Member
    Location
    Orange, California, USA
    Member No: 184053 master6 is on a distinguished road master6's Avatar
    Join Date
    Nov 2010
    Posts
    71
    Rep Power
    6


    Yes | No

    DIY Brake servo (booster) re-build with new o-rings and a new shaft seal

    For the following cars 533,535,m535,m5,633,635,m635,m6,735.

    This Do It Yourself (DIY) is to re-build the Brake Servo Booster #34331156925
    It includes a step by step procedure to repair the internal rubber seal and 5 o-rings.
    I just up dated this post DIY, I have added a new shaft seal and a how to replace the seal.

    Read the captions at the bottom of each photo.

    https://picasaweb.google.com/1135658...nZ_Z7f6JrUyQE#

    This repair needs to have the booster removed from the car.

    Tools needed: Dremal, vise, bench grinder, battery drill motor with reverse, 1-1/8 inch deep socket, 13mm 1/4 in drive socket with an extension into the drill motor, blade screw driver, 10mm drill bit or 3/8 inch metal drill bit, electric drill motor with 3/8 chuck.
    Reply With Quote Reply With Quote 67.49.70.48


  2. #2
    Registered Member
    Location
    Orange, California, USA
    Member No: 184053 master6 is on a distinguished road master6's Avatar
    Join Date
    Nov 2010
    Posts
    71
    Rep Power
    6


    Yes | No

    New update I found a supplier for the internal white teflon (2) high pressure o-rings

    Hi forum members,

    I located a supplier for the internal white teflon (2) piston rings. I should have them in about 15 days.

    I also found a supplier for the internal shaft seal at a lower price, 9.5mm I.D. This will take about 8 weeks to manufacture.

    Then I will have all of the interior replacement parts, a complete repair kit, for the brake servo/booster.

    Here is the photo link to the DIY re-build.

    https://picasaweb.google.com/1135658...nZ_Z7f6JrUyQE#

    Read the captions at the bottom of each photo.

    I also added a new helpfull hint for the re-build.
    Where the grub screw, screws into the booster cylinder there can be a burr created by the grub screw, on the interior. This burr can cut the 38mm O-ring, and also damage the 2 white high pressure teflon piston rings.
    Thanks to (tn).

    When I receive these new parts, I will revise the price.
    Reply With Quote Reply With Quote 67.49.70.48

  3. #3
    Unregistered
    Guest
    Location
    , ,
    Member No: Unregistered's Avatar


    Yes | No

    kit

    Hi Jay,
    I tried to respond to your PM on another site and apparently when I updated
    my email address, I'm blocked from posting messages or checking my PMs.

    I need your kit to attempt a fix on my booster and also your recommendation
    for changing the pressure bomb or not.

    Tom
    Reply With Quote Reply With Quote 38.114.199.121

  4. #4
    Unregistered
    Guest
    Location
    , ,
    Member No: Unregistered's Avatar


    Yes | No
    Tom,

    Contact me via my e-mail jay_c_stratton at hotmail.com
    Reply With Quote Reply With Quote 67.49.71.23

  5. #5
    Registered Member
    Location
    , ,
    Member No: 58142 ROYinGA is an unknown quantity at this point ROYinGA's Avatar
    Join Date
    Nov 2002
    Posts
    2,633
    Rep Power
    0


    Yes | No
    Checking the bomb. Take a small straw and stick it in the hole in the bomb. Good is when the straw goes in about 3/4" and bad is when it goes all the way in.
    Reply With Quote Reply With Quote 66.32.155.225

  6. #6
    Registered Member
    Location
    Orange, California, USA
    Member No: 184053 master6 is on a distinguished road master6's Avatar
    Join Date
    Nov 2010
    Posts
    71
    Rep Power
    6


    Yes | No

    New-Upgraded DIY rebuild kit for the Brake Servo Booster

    Hi Forum Members,

    I now have all of the interior components for the complete re-build of the Brake Servo (booster). I have received the new teflon interior high pressure piston o-rings. I installed these new parts into my M6 over the weekend. The road test was a success, all of the parts work as they should!

    The new up-graded kit includes the 5 internal rubber o-rings, the 2 teflon piston o-rings, and a new shaft seal.

    I have also up-graded the Picasa Link, I took more photos and added more captions to show the correct method that I used in the assembly of the booster.

    The new price is $24.95 + shipping $1.95 USA, TOTAL $26.90 USD.

    International is also $24.95 + shipping $3.95 International TOTAL $28.90 USD.

    Here this the link to the DIY, step by step instruction, of the booster repair.

    https://picasaweb.google.com/1135658...nZ_Z7f6JrUyQE#

    I am also offering a QUICK FIX kit, this includes just the 38mm o-ring, and the shaft seal only. Price is $7.95 + $1.95 shipping USA TOTAL $9.90 USD.
    International is also $7.95 + $3.95 shipping International TOTAL $11.90 USD.
    Reply With Quote Reply With Quote 67.49.71.23

  7. #7
    Registered Member
    Location
    Orange, California, USA
    Member No: 184053 master6 is on a distinguished road master6's Avatar
    Join Date
    Nov 2010
    Posts
    71
    Rep Power
    6


    Yes | No

    Hydraulic brake servo booster 10 piece repair kit and Repair Service

    Hi Forum Members,

    For the following BMW cars
    e28,533,535,m535,m5, part # 34331156925
    e24,633,635,m635,m6,L6, part # 34331156925
    e32,735 only. part # 34331156925

    e23,733,735,745 part # 34331152825

    This Do It Yourself (DIY) is to re-build the Brake Servo Booster, all of the 10 piece interior repair kit are identical, for both part numbers

    I recently rebuilt another hydraulic brake servo booster, and I was amazed at how the rubber o-rings were deformed and hardened. They are now an oblong shape. The large o-ring 38.0mm x 3.0mm, at the front of the booster. It now measures 2.55mm high instead of 3mm. And is 3.28mm thick, were it should be again be 3.0mm. And it is noticeably more brittle. The smallest o-ring was brittle and it broke when removed.

    https://picasaweb.google.com/1135658...nZ_Z7f6JrUyQE#

    I am now offering to rebuild your booster for you, using my 10 piece repair kit.
    I am charging $85.00 + shipping back to you. Cont USA only. USD
    If you send me your address, and I can give you an accurate shipping quote, via FedEx Ground home delivery.
    Just send your booster to me, with a $ check. PayPal add 4%

    I also have a couple of spare rebuilt booster, that I can send to you. And you return your old core to me, shipping on you.
    Same price of $85.00 + ship + $60.00 core. USD
    PayPal add 4%
    [email protected]

    _________________
    Jay
    1987 M6
    https://picasaweb.google.com/1135658...X_js7i1IyIgAE#
    Booster rebuild
    https://picasaweb.google.com/1135658...nZ_Z7f6JrUyQE#
    Reply With Quote Reply With Quote 72.130.2.5

  8. #8
    Registered Member
    Location
    Orange, California, USA
    Member No: 184053 master6 is on a distinguished road master6's Avatar
    Join Date
    Nov 2010
    Posts
    71
    Rep Power
    6


    Yes | No

    Changes 2-8-13

    DIY brake servo booster repair kit and rebuild service.

    Please read the captions under each photo.

    https://picasaweb.google.com/1135658...nZ_Z7f6JrUyQE#
    Reply With Quote Reply With Quote 72.130.2.5

  9. #9
    Registered Member
    Location
    Orange, California, USA
    Member No: 184053 master6 is on a distinguished road master6's Avatar
    Join Date
    Nov 2010
    Posts
    71
    Rep Power
    6


    Yes | No

    Special note! Please read! Some BAD boosters are being sold.

    Hello e28 owners,

    Parts Geek and its supplier A-1 Cardone, are selling bad rebuilt hydraulic brake boosters.

    I had a client of mine who sent me a leaking booster. When I opened it up to repair, I noticed that it had an incorrect shaft seal installed.

    On top of that, the shaft seal was installed up-side down, and missing the garter spring.

    My client told me that his first Cardone from Parts Geek leaked as soon as it was installed, he sent it back to Parts Geek and they sent him another.

    When he installed the second one, it also leaked.
    And thats when he called me, and I used my rebuild service and sent him one of my rebuilt spares.

    When I received his core back, I set to rebuild it for the next client.
    I was shocked, the shaft seal was upside down, I then pressed the shaft seal out of the black plastic cup. The shaft seal specs are 9.5mm i.d. x 22.0mm o.d. and thickness of 6mm.
    The A-1 Cardone is 10.0mm i.d., way too big. It is made in China by YEI Shien, part #A19168 10x22x6.
    Because it was in backwards the garter spring came off, or was never there in the first place.
    I am going to also attach some photos, of the suspect seal front and back, and what a garter spring looks like.

    Here is my link, booster repair kit and rebuild service.

    https://picasaweb.google.com/1135658...nZ_Z7f6JrUyQE#

    Thank you,

    P4190001.JPGP4190003-001.JPGP4190004-001.JPG
    Reply With Quote Reply With Quote 72.130.2.5

+ Reply to Thread


Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

     

Similar Threads

  1. Homelink re-learn with new batteries-nice improvem
    By davidfarmer in forum BMW X5 SAV Forum (E53)
    Replies: 1
    Last Post: 04-02-2004, 04:13 PM
  2. need brake servo booster unit 2000 CS
    By Joe K in forum BMW CS Forum (E9)
    Replies: 0
    Last Post: 11-22-2001, 05:05 PM
  3. Group letter to BMWNA re issues with new cars (m)
    By '00 323iA in forum BMW 3 Series Forum (E46)
    Replies: 1
    Last Post: 12-04-2000, 07:47 PM
  4. Brake lining light still on with new sensors....
    By Don76 in forum BMW 3 Series Forum (E30)
    Replies: 2
    Last Post: 08-11-2000, 11:20 PM
  5. 46% owners of BMW and they're unhappy with new E46
    By Steve in forum BMW 3 Series Forum (E36)
    Replies: 3
    Last Post: 02-17-1999, 11:23 AM

Bookmarks

Posting Permissions

  • You may post new threads
  • You may post replies
  • You may not post attachments
  • You may not edit your posts
1e2 Forum